PRODUCT
A quick drying nitrocellulose primer cum surfacer designed for wood or wood substitutes. The product has excellent filling & sanding property in addition to its protective value. Quicker drying feature along with superior filling & sanding properties make it ideal for high out-put requirement as well as rich finish when used in combination with Britex NC pigmented topcoat.
FEATURES
- Quick drying hence fast turnaround & less dirt pickup
- Very good filling & sanding properties
- Interior & exterior use
RECOMMENDED USE
Natural wood & wood substitutes like fibre board, veneer etc. Suitable for interior &
exterior use.
SPECIFICATIONS AND OTHER INFORMATION
Finish : Smooth & matt
Color : Light grey & White
NVM% : 55-57
Gloss at 60 degree : 10-15%
Supply viscosity ;120-130 KU at 300 C
Thinner :NC Thinner MT-3/ MT-2/ MT-1
Thinning Ratio (vol) : 1:1
Method of application : Conventional spray , Brush ( over a small area)
Shades : As per company shade card
Theoretical coverage : 7-8 m2/lt at 30 micron DFT
Practical coverage : would depend on the surface profile, application skill & method, loss in the container.
Drying time (@30oC) : Surface dry 10-12 minutes
Sandable dry :1 hr @30oC
Hard dry : 3-4 hrs @30oC
Stackable dry : 4 hrs @30oC
Pack size : 1USG,5USG
SURFACE PREPARATION AND APPLICATION
The product is best applied by conventional spray although application by brush is possible over a small area. Avoid brush application over a large surface area.
Ensure wood is dry, clean & free from contaminants. Sand the surface with a coarse (P180) followed by fine sandpaper (P 400) along the direction of grains. Dust off the surface & apply a coat of Britex filler if required. Allow it to dry for 1 hr & sand off the excess filler & clean the surface. Apply a coat of Britex N.C primer surfacer after thinning with NC thinner. Allow it to dry for one & half hour, flat the surface using P400 Emery paper, dust off & apply two coats of Britex N.C pigmented topcoat after thinning with NC thinner.
STORAGE AND HANDLING
Storage & Disposal Store in cool, dry condition keeping container tightly closed in accordance with petroleum (mixture) order, SRO 1929 No 993. & dispose by controlled land fill as per requirement of statutory authority. Don’t empty into drains, sewers or other water courses.
Flash Point : Below 20oC,Highly flammable.
Shelf Life : Upto 12 months in closed condition
SAFETY PRECAUTIONS AND FIRST AID
- Avoid contact with the skin and eyes. Wear suitable protective clothing such as overalls, goggles, dust mask and gloves. Use a barrier cream.
- Ensure that there is adequate ventilation in the area where the product is being applied. Do not breathe vapor or spray.
- This product is flammable. Keep away from sources of ignition. Do not smoke. Take precautionary measures against static discharge. In case of fire, blanket flames with foam, carbon-dioxide or dry chemicals.
- Eyes & Skin: In the event of accidental splashes, flush eyes with warm water & wash skin with mild soap and seek quick medical advice. Never use solvent for cleaning the affected areas.
- Inhalation & Ingestion: Remove to fresh air, loosen collar. Don’t induce vomiting.
DISCLAIMER
The product information sheet is meant for general information of the product. Optimal performance by the product would be achieved on correct selection of paint & painting system, proper surface preparation & application. The information in this data sheet is provided to the best of our knowledge. However, we have no control over either quality or condition of the substrate and other factors affecting the use and application of this product. Therefore, we cannot accept any liability whatsoever or howsoever arising from the performance of the product or for any loss or damage arising from the use of this product.
Product information sheet would be subject to modification as & when product is modified/improved. Our endeavor would be to keep you abreast of change.