PRODUCT
BRITEX acid curing lacquer is a premium quality alkyd – melamine system cured by acid catalyst. The product is designed for protective & decorative coating for wood & wood substitute.The product on full cure forms a very surface hard coating, resistant to oils, foods, hot beverage, alcohol & various solvent.The finish offered by the product is one of the best among popular wood coatings. BRITEX Acid curing lacquer is ideal for office & domestic furniture & is very suitable for interior use. Available in matt, silk-matt & gloss version.
FEATURES
.Excellent finish
.Very good surface hardness combined with flexibility
.Economic
.Good chemical resistance
COMPOSITION
.Short oil non drying oil alkyd
.Melamine formaldehyde resin
.PTSA Catalyst
RECOMMENDED USE
Wood or Wood substitutes like Fibre board,Veneer, Plywood etc. Particularly suitable for wooden furniture, doors, windows & frames for interior use.
SURFACE PREPARATION AND APPLICATION
Conventional spray, automatic sprinkler, curtain coating are most recommended method of application. Brush application for touch up only.
Ensure wood is dry, clean, free from grease & other organic contaminants, well sanded ( with emery paper P180 followed by P400 along the direction of grains) & dusted. Soak the surface with MELAMINE thinner with the help of sponge or rag for 10 minutes before application. (Very useful on hard wood surface. )
Apply two coats of Britex wood AC sanding sealer with a gap of max 10 minutes between the coats.
This is a two part product. Mix Base, Hardener & Thinner ( if required) as per ratio mentioned in the can. Mix thoroughly & wait for 10 minutes before application for effervescence to subside. Allow to dry & thoroughly sand the surface after two hours dust off & clean the surface. Apply two coats of Britex AC clear with an interval 10-15 minutes. Ensure adequate ventilation during mixing ,application and drying. Do not apply when humidity exceeds 95% and condensation is likely. Only apply coating when surface temperature is 3ºC or more above dew point.
May require additional 5-7% thinner depending on ambient temperature & method of application.
SPECIFICATION AND OTHER INFORMATION
Finish : Smooth with excellent flow & surface characteristics.
Gloss at 600 : Intense matt – 5-10% & Silk-matt 30-35%.
Gloss > 90%
NVM % : 53-55
Supply viscosity : Gloss 60-70 sec Matt/Silk-matt 85-95 sec at B4/30oC Mixing ratio : Base : Hardener = 9:1 ( vol)
Thinner/ Tool cleaner : Melamine thinner
Method of Application : Conventional spray, Curtain coat, Automatic Sprinkler
Pot life : 8 hrs at 30oC deg c
Recoating interval : 4 hrs
Theoretical Coverage : Approx 13 m2/lt at 30 microns DFT.
Practical coverage : would depend on the surface profile, application skill & method, loss in the container.
Drying time @ 30oC : Surface dry 30 minutes
Hard dry over night
Pack size : 1USG & 5 USG
STORAGE AND HANDLING
Storage & Disposal : Store in cool, dry condition. & dispose by controlled land fill as per requirement of statutory authority. Don’t empty into drains, sewers or other water courses.
Avoid part use of the Hardener. It is filled in specific quantity.
Flash Point : 22oC
Shelf Life : Upto 12 months in closed condition
SAFETY PRECAUTIONS AND FIRST AID
Avoid contact with the skin and eyes.Wear protective clothing such as overalls, goggles, dust mask and gloves, Use a barrier cream.
Ensure that there is adequate ventilation in the area where the product is being applied. Do not breathe vapour or spray.
This product is flammable. Keep away from sources of ignition. Do not smoke. Take precautionary measures against static discharge. in case of fire, blanket flames with foam, carbon-dioxide or dry chemicals.
In the event of accidental splashes, flush eyes with warm water & wash skin mild soap and seek quick medical advice, Never use solvent for cleaning the affected areas.
Inhalation & Ingestion : Remove to fresh air, loosen collar. Dont’t indice vomiting Refer MSDS for Details
DISCLAIMER
The Product information sheet is meant for general information of the product. Optimal performance by the product would be achieved on correct selection of paint & painting system, proper surface preparation & application. The information in this data sheet is provided to the best of our knowledge. However, we have no control over either quality or condition of the substrate and other factors affecting the use and application of this product. Therefore, we cannot accept any liability whatsoever or howsoever arising from the performance of the product or for any loss or damage arising from the use of this product. Product information sheet would be subject to modification as & when product is modified / improved. Our endeavor would be to keep abreast to the change.