NC Glossy Clearnc_glossy_clear
Preloader Close

maheshwari.hsp@gmail.com, info@maheshwarisyn.com

NC Glossy Clear

NC Glossy Clear

PRODUCT

A very fast drying single pack Nitro Cellulose based clear gloss lacquer. The product is very suitable for use as interior wood coating for Furniture, Doors / windows, Wooden partition etc. preserving the natural look of wood. The product is generally recommended for interior purpose nevertheless can be used externally if the environment is not too harsh & the painted substrate is partially exposed. It’s fast drying property make it attractive for higher productivity.

FEATURES

  • Very fast drying hence higher productivity & less dirt pick up
  • Easy re-workability
  • Can be applied by brush over a small area

RECOMMENDED USE

Natural wood & wood substitutes like fiber board, veneer etc. More suitable for interior use.

SPECIFICATION AND OTHER INFORMATION

Finish                                 : Smooth & glossy

NVM%                                : 38-40

Gloss at 60 degree               : 78-82%

Supply viscosity                   : 115-120 KU @30oC

Thinner                               : NC THINNER MT-3/MT-2 /MT-1

Thinning Ratio (vol)              : 1:1 for Brush application & 1:2 for spray application

Method of application            : Conventional spray, Brush ( over a small area)

Theoretical coverage             : 7-8 m2/ltr at 40 micron DFT

Practical coverage             : Would depend on the surface profile, application skill & method, loss in the container.

Drying time @30oC           : Surface dry 10-12 minutes

Sandable dry                        : 1 hr

Hard dry                              : 3-4 hrs

Stackable dry                       : 4 hrs

Pack size                              : 1USG, 5USG

SURFACE PREPARATION AND APPLICATION

The product is best applied by conventional spray although application by brush is possible over a small area. Avoid brush application over a large surface area. Ensure wood is dry, clean & free from contaminants. Sand the surface with a coarse (180) followed by fine sand paper (400) along the direction of grains.

Dust off the surface & apply a coat of Britex filler if grain filling is required. Allow it to dry for 1 hr & sand off the excess filler & clean the surface. Apply a coat of Britex N.C sanding sealer after thinning with Britex NC thinner Allow it to dry for 45 minutes. Sand off & clean the surface & apply two coats of Britex NC clear topcoat after thinning with Britex NC thinner.

Don’t use filler if grain filling is not required. Avoid application of NC products under high humidity to avoid blooming. Also NC products are not advised over enamel. It would lead to lifting of the underneath coat.

STORAGE AND HANDLING

Storage & Disposal   : Store in cool, dry condition. & dispose by controlled land fill as per requirement of statutory authority. Don’t empty into drains, sewers or other water courses.

Shelf Life             : Upto 12 months under sealed condition.

SAFETY PRECAUTIONS AND FIRST AID

  • Avoid contact with the skin and eyes. Wear suitable protective clothing such as overalls, goggles, dust mask and gloves. Use a barrier cream.
  • Ensure that there is adequate ventilation in the area where the product is being applied. Do not breathe vapor or spray.
  • This product is flammable. Keep away from sources of ignition. Do not smoke. Take precautionary measures against static discharge. In case of fire, blanket flames with foam, carbon-dioxide or dry chemicals.
  • Eyes & Skin: In the event of accidental splashes, flush eyes with warm water & wash skin with mild soap and seek quick medical advice. Never use solvent for cleaning the affected areas.
  • Inhalation & Ingestion: Remove to fresh air, loosen collar. Don’t induce vomiting.

DISCLAIMER

The product information sheet is meant for general information of the product. Optimal performance by the product would be achieved on correct selection of paint & painting system, proper surface, surface preparation & application. The information in this data sheet is provided to the best of our knowledge. However, we have no control over either quality or condition of the substrate and other factors affecting the use and application of this product. Therefore, we cannot accept any liability whatsoever or howsoever arising from the performance of the product or for any loss or damage arising from the use of this product.

Product information sheet would be subject to modification as & when product is modified/improved. Our endeavor would be to keep you abreast of change.