Mypoxy HB ZP 550mypoxy_hb_zp_550
Preloader Close
X

About Us

From the manufacturing of Gum Rosin and Natural Turpentine oil, adding on to various types of Varnishes and coatings of old times.

About Us

Contact Info

maheshwari.hsp@gmail.com, info@maheshwarisyn.com

01882-238688, 238439

Mypoxy HB ZP 550

Products->Protective Coatings->Epoxy

Mypoxy HB ZP 550

 

Product

Mypoxy HBZP 550 is a medium solid, high build two component anti corrosive epoxy primer. It contains high amount of Zinc Phosphate as corrosion inhibiting pigment for protection in extreme environments.

Recommended Use

Mypoxy HBZP 550 is recommended where high DFT is required as part of protection system such as highly Humid, Corrosive and Chemical environments, Cement Plants, Refineries, Bridges, and other Chemical Industries. It is also suitable for equipments to be installed in those areas/ environments.

Specification & Other Information
Colour

: Grey, Red Oxide

Finish

: Matt to Eggshell

Soiled by Volume

: 55 ± 2%

Supply Weight (Kg/Ltr)

: 1.55±0.05

Flash Point

: 29° C

Dry Heat Resistance

: Intermittent : 120°C, Continuous: 100°C
Shelf Life : 12 months
Dry Film Thickness

: 70-100µ in single coat
Wet Film Thickness

: 125-180µ in single coat
Theoretical Coverage Rate : 7.85 sq.mt / lit at recommended DFT of 70µ

Surface Preparation

All surfaces to be coated should be clean, absolutely dry and oil or moisture free before painting application. Oil and grease should be removed by solvent cleaning.

Repair Cases: Corroded areas should be power tool cleaned to St3 or blast cleaned to Sa2 or better. Existing system should be dry and free from loose paint, salt, grease and other contaminants prior to overcoating.

New steel: Abrasive blasting to Sa 2½ (ISO 8501-1:2007). For temporary protection, if required, use a suitable shopprimer. All damage of shopprimer and contamination from storage and fabrication should be thoroughly cleaned prior to final painting.

Maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Clean damaged areas thoroughly by power tool cleaning to St 3 (ISO 8501-1:2007) (minor areas) or by abrasive blasting to min. Sa 2, preferably to Sa 2½ (ISO 8501-1:2007). Improved surface preparation will improve the performance of the product.

Stainless steel: To be abrasive blast cleaned to a uniform, sharp, dense profile (ISO Comparator Medium (G), corresponding to Rz minimum 50 micron. Any salts, grease, oil, etc. to be removed before abrasive blasting is commenced.

Application Data
Application Method

: Spray/ Airless Spray/Brush/ Roller

Mixing Ratio

: 5 Part (Base) : 1 Part (Hardener)

Pot Life

: Four Hours at 30°C

Thinner and Cleaner 

: Britex Epoxy Thinner 

Airless Nozzle Orifice

: 0.45 - 0.58mm

Nozzle Pressure

: 176 kg/cm² or 2500 psi

Working Precautions: Material should not be allowed to remain in pipeline, hoses, gun or spray equipment. Thoroughly flush all equipment with Britex Epoxy thinner. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages, the work should recommences with freshly mixed units.

Maintenance: Clean all equipment immediately after use with Britex Epoxy thinner. It is good working practice to periodically flush out spray equipment during the course of the working day. All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.

Drying Characteristics
Surface Dry

: 60 mins

Touch Dry (to handle)

: 3 Hours

Hard Dry

: 24 Hours

Overcoating Interval

: Minimum 3 Hours
Drying and curing times are determined at 30°C under controlled temperatures and relative humidity below 85%, and at average of the DFT range for the product.

Compatibility
Previous Coating

: Epoxy

Subsequent Coating

: Epoxy, Polyurethanes, Alkyds, Modified Alkyds, Acrylics

Storage

This is solvent based coating and the containers should be kept in a dry, cool, well ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed.

Caution

This product is for professional use only. The paint applicators should be trained, experienced and have the capability and equipment to mix and apply the coatings correctly as instructed. Applicators should use appropriate protection equipment when using this product.

This is solvent based product and should be use under well ventilated conditions. Do not inhale spray mist. Skin contact should be avoided. In case of spillage on the skin, it should immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with water.

Limitation of Liability
This information is given to the best of our knowledge. Because of the multitude of formulations, production, and application conditions, all the above-mentioned statements have to be adjusted to the circumstances of the processor. Our products are often used under conditions beyond MSPL's control. MSPL cannot guarantee anything but the quality of the product itself. No liabilities can be derived from this fact for individual cases. This issue replaces all previous versions – Printed in India.